What steps should you follow to start a vehicle that has a dead battery quizlet?

What steps should you follow to start a vehicle that has a dead battery?

Turn off the ignition on both cars. First, clamp one end of the positive cable to the dead battery’s positive clamp. Now have a helper connect the other end of that cable to the other battery’s positive clamp. Next, connect the negative cable to the negative terminal on the good battery.

When jumping a dead battery which car do you start first quizlet?

After waiting for some time, start the “dead” car. It should start. 7. Disconnect the black jumper cables first, then disconnect the red ones.

THIS IS IMPORTANT:  Question: How long should a brand new transmission last?

When jump starting your car the negative electrical cable will probably be colored red and the positive electrical cable will probably be colored black?

One is marked positive (+), the other negative (-). There are also positive and negative cables in the jumper cable set. The red one is positive (+), the black one is negative (-). Never connect the red cable to the negative battery terminal or a vehicle with a dead battery.

When jumping a car battery the proper order of the steps are quizlet?

Terms in this set (10)

  1. Put the red clamp on the positive terminal on the car with the dead battery.
  2. Put the red clamp on the postive terminal on the car with the good battery.
  3. Put the black clamp on the negative terminal on the car with the good battery.

What are the steps to starting a car?

How to start a vehicle

  1. Place your key in the ignition and turn it to the ‘on’ (third) position.
  2. Press the brake pedal.
  3. Switch the gear to Drive (D).
  4. Lift your foot from the brake and press the accelerator gradually to start moving. (30)

What steps should you follow to start a vehicle that has a dead battery Chapter 17?

Terms in this set (9)

Take out your jumper cables. Place both vehicles in Park or Neutral and shut off the ignition in both cars. Engage both parking brakes as well. Attach one of the red clips to the positive terminal of your battery.

How often should you try to start the dead car during the jump start process?

Then try to start the dead car. If the car sounds like it’s trying to turn on but isn’t quite there, leave it off and let the live car run for a few more minutes. Try again every minute for about 5 minutes. Eventually, your car should start.

THIS IS IMPORTANT:  Quick Answer: How long does an automatic transmission usually last?

When jump starting a vehicle that has a dead battery drivers Ed?

Batteries give off gases, and those sparks could cause an explosion. So we’re not going to hook it up directly to the battery, but rather, something metal like the chassis. Make sure the cables are clear of any moving parts like fan blades, start up the good car, wait about five minutes, and then try the dead one.

What is the first thing you must do to regain control of a vehicle that veered off the highway?

What is the first thing you must do to regain control of a vehicle that’s veered off the highway? Remain calm.

When jump starting a car always remember positive to negative?

The positive (red) cable should be attached to the positive terminals on each battery. The negative (black) cable should have one end attached to the negative terminal of the dead battery, and one end grounded.

When jump starting a car make sure the car?

You can jump start the car without cables. Depress the clutch and put the car in first gear, then turn the ignition to on. On a clear stretch of road, either start the car rolling down an incline or get friends to push you. When the car reaches 5-10 mph, release the clutch.

What do you do before connecting the jumper cables?

To hook up jumper cables, you typically need two cars. Pop both hoods, and then connect the red and black clamps to the battery in the car that won’t start. Then do the same to the other vehicle. Start the working car, and let it idle for a minute.

THIS IS IMPORTANT:  Your question: Can tinted car windows be lightened?

What should you do if you have a tire blowout quizlet?

What should you do during a tire blowout? Take foot off gas, don’t use brakes, concentrate on steering, slow down gradually, brake softly when car is under control, pull completely off pavement/roadway.

How do you hook up jumper wires?

4. Connect the Jumper Cables Correctly and Safely

  1. i) Connect one clamp of the positive (red) cable to the dead battery’s positive terminal.
  2. ii) Connect the other red clamp to the positive post of the working battery.
  3. iii) Attach one clamp of the negative (black) cable to the negative post of the working battery.