What are the numbers stamped on the engine block used for?

What does the engine block number mean?

Engine blocks can be identified by their casting numbers. A alphanumeric code is generally used to identify a block’s series number, displacement range, casting location, and date of manufacture. There are different locations depending on the manufacturer and engine type.

What are the numbers on my engine?

Your VIN number is your vehicle identification number and you can find your engine size by VIN number. In the series of numbers and letters, the tenth from the left denotes the model year and the eighth is the engine codes. Just tell the store clerk those two characters and you’re in business.

What do Chevy block numbers mean?

You can identify a Chevy by the numbers on its engine block, recorded in an official Chevy engine block registry. The identification number consists of a seven-to-eight digit code. The prefix consists of five digits and explains the date and the location of the Chevy’s manufacture.

THIS IS IMPORTANT:  Why is methanol used in windshield washer fluid?

How do you decode a Ford engine block?

A = 1940s, B = 1950s, C = 1960s, D = 1970s, E = 1980s, F = 1990s. The second digit will be a numeral, and will represent the year within that decade (i.e. C2 = 1962; E7 = 1987). The third digit is usually another letter, but can also be a numeral in rare cases, and it signifies the vehicle the part was designed for.

How do I identify my Ford engine block?

The casting numbers are located in the section of the block where Ford stamped them. Illuminate the area where Ford stamped them. You will find this on the starter mount, where the starter motor bolts to the engine. Write down the casting number on a piece of paper and pen.

How can you tell the difference between a 350 and a small block 400?

Check the bore on the engine if the heads are off. The Chevy 350 cubic inch engine has a 4-inch bore whereas a 400 cubic inch engine has a 4.125-inch bore. The 350 has a 3.48-inch stroke, and the 400 has a 3.75-inch stroke.

How do you tell if my motor is a 350 or 305?

Matching the suffix portion of the engine ID number properly identifies the engine as a 305 or 350 cubic-inch. If a bore measurement is to be taken, Popular Hot Rodding identifies the 305s small bore at 3.736 inches. Both the 305 and 350 have the same 3.48-inch stroke.

How do I identify a ZZ4 engine?

ZZ4 blocks were painted black and the black valve covers have retaining bolts along the valve cover center, not along the edges as with previous small blocks. The timing chain cover is black 200 mph rated black plastic. The ZZ4 came with an HEI distributor and a cast iron water pump.

THIS IS IMPORTANT:  Will disconnecting battery reset transmission?

How can I tell what year my engine block is?

The engine will have a alphanumeric casting number on the passenger side (right side) of the block, under the heads. The first letter of the code identifies the decade (C=1960s, D=1970s, E=1980s), the second digit in the code identifies the specific year.

How many digits are in an engine number?

Each of these 17-digits signifies important statistics of your car.

How do I know if my Chevy engine is a 427?

The surest way to identify a 427 engine is to decode the engine casting number located on the engine block.

  1. Locate the engine casting number on the rear of the engine block on the bell housing flange.
  2. If the number is 3909802, it is a 427 produced from 1966 to 1967.

How do I identify a Chevy big block engine?

The first indication that a motor is a Big Block Chevy is if the codes are stamped above the timing chain cover. All Big Blocks are stamped there. Small Blocks are stamped on a pad in front of the passenger side cylinder head and are often covered by the alternator.

How do you tell a 327 from a 350?

Measure the stroke. If the stroke is 3.25 its a 307 or 327. If its 3.48 its a 350.